Skip to content
  • Part of the Kee Safety Group
  • SafeContractor accredited
  • Constructionline member

Blog

Deadweight Roof Anchors Explained: How Kee AnchorĀ® Keeps Workers Back From the Edge

Not every roof can take a fixed anchor. A warranted single ply membrane, an asphalt roof that would need cutting, or a structure that can’t be reached all rule out drilling and bolting. Deadweight roof anchors solve this by providing fall protection without touching the roof membrane. Used in fall restraint, they stop workers reaching the edge in the first place. This overview explains how the Kee AnchorĀ® system works, where it suits, and when another safety solution is the better choice.

What Is a Deadweight Roof Anchor?

A deadweight anchor is a mobile anchor device that sits on the roof surface and is held in place by its own mass. Nothing is drilled, bolted or bonded, so the roof covering and waterproofing stay intact.

Deadweight roof anchors belong to a wider group known as mobile man anchor systems. These anchor devices give workers a secure attachment point where permanent anchors or collective protection aren’t viable. Kee Anchor is tested to BS EN 795:2012 Type E, the class covering deadweight anchors, and designed in line with BS 7883:2019.

How the Kee AnchorĀ® Anchor System Works

Kee Anchor deadweight roof anchor installed on a flat building roof
A Kee Anchor deadweight roof anchor sitting on a flat roof, with nothing fixed into the roof membrane.

The Kee Anchor deadweight anchor system has a simple layout. Four stacks of weights sit at the corners of a 1400mm square, with two cross arms meeting at the centre and a stabiliser arm along one side. Each base weight is fully encased in a rubber moulding, so rubber rather than steel sits on the roof.

The attachment point is a central pedestal, raised above the weights. It takes the safety harness lanyard and raises the height at which any arrest force is applied. As a result, part of the load presses the weights into the roof, so the anchor moves less if a fall happens.

This mobile anchor system is modular, assembled on the roof from a small number of parts. It can be dismantled and moved as work moves around the site. Beyond a single anchor point, Kee Anchor can also act as a lifeline post linked with Kee LineĀ®, or as a portable anchor for rope access work.

Fall Restraint: Keeping Workers Back From the Edge

Kee Anchor deadweight roof anchor installed on a flat building roof
A worker attached to a Kee Anchor on a flat roof. In fall restraint, the lanyard length is set so the edge can’t be reached.

Fall restraint is about prevention. A fixed-length lanyard, set at survey, means the worker physically can’t reach the edge. If they can’t reach it, they can’t fall from it.

With Kee Anchor in fall restraint, up to two workers can be attached at once, provided neither can get closer than 500mm to the roof edge. The working radius is set by the lanyard length for that specific roof.

This matches the Work at Height Regulations 2005, which favour preventing a fall over arresting one. Kee Anchor can be used for fall arrest with an energy-absorbing lanyard. However, fall restraint is always the preferred mode where the task allows it.

Where a Mobile Man Anchor Makes Sense

A mobile man anchor earns its place where a fixed anchor system isn’t practical. A few examples include warranted membranes, flat roofs where the structure below can’t be reached, and short-term or low-frequency maintenance work that needs safe access to rooftop plant.

Kee Anchor is approved for a range of roof types, wet or dry: single ply membrane, asphalt, steel cladding, concrete, brushed stone chippings and mineral felt. It suits roofs up to 5° pitch and is hot dip galvanised to BS EN ISO 1461. Because performance depends on the correct model for each roof surface, Mantech confirms the model at survey.

When a Man Anchor System Isn’t the Right Fall Protection

A man anchor system works best when work happens at one location, which is true of all mobile man anchor systems. Where workers need to move across the roof, a Kee LineĀ® horizontal lifeline gives continuous fall protection instead. Posts and eyebolts offer a permanent fixed anchor, while Kee GuardĀ® provides collective protection such as handrails and safety barriers, with no harness needed.

Collective protection should always be considered first. Deadweight roof anchors are the right answer when it isn’t practical, not a default.

Getting the Right Deadweight Roof Anchors for Your Site

Our team surveys the roof first, recording the surface, pitch, edge distances and the work involved. We then confirm the right model against current manufacturer’s data. Each deadweight anchor is supplied, installed and certified at handover with supporting documents, then inspected annually against the relevant standards to keep your rooftop safety compliant.

Contact Mantech

If you’re weighing up deadweight roof anchors for a roof that can’t be drilled, talk to our safety experts today. We’ll survey your roof, review your specific safety requirements and safe access needs, and recommend the right fall restraint or safe access solutions for your site.

Got a question about working at height?

A free site survey answers it in one visit — with a fixed quote to follow.

  • Over 25 years protecting UK rooftops
  • SafeContractor accredited, Constructionline member
  • Survey, installation and annual testing by one team

Prefer to talk?

Monday to Friday, 08:30 - 17:00

We reply within one working day. No obligation.

Talk to an expert Call 01278 228180